Ika RH digital User Manual download pdf (Page 12)

Unpacking

•Unpacking

- Please unpack the device carefully

- In the case of any damage a report must be sent immediately

(post, rail or forwarder).

•Contentsofpackage

- Magnetic stirrer with heating RH basic or RH digital

- Mains cable - Operating Instructions

- Screwdriver - H 102.1 Protection handle

- H102 protective cover (RHb) - H103 protective cover (RHd)

- Stirring bar 20, 30 and 40 mm

Correct use

•Use

- For mixing and/or heating liquids.

•Rangeofuse(onlyindoors)

- Laboratories - Schools

- Pharmacies - Universities

This device is suitable for use in all areas except:

- Residential areas

- Areas that are connected directly to a low-voltage supply net-

work that also supplies residential areas.

The safety of the user cannot be guaranteed if: the appliance is

operated with accessories that are not supplied or recommended

by the manufacturer, the appliance is operated improperly accor-

ding to the manufacturer’s speciﬁcations or the appliance or prin-

ted circuit board are modiﬁed by third parties.

Commissioning

Please follow above directions to ensure safe operation and

prevent device from suffering damage.

The device is switched on and off using the main switch (A) on the

right hand side.

After the device has been switched on using the main switch (A) the

“power“ LED (E) lights up; this indicates standby status.

The device is now ready to operate. If the heating function is switched

on, the LED (F) lights up, indicating that the heating process is active.

RH digital

Observe the ambient conditions (temperature, humidity, etc.) listed

under Technical Data.

Make sure the contact plug (N)is plugged in.

Once this condition is satisﬁed, and the mains plug has been plugged

in, the device is ready to operate.

Please follow above directions to ensure safe operation and prevent

device from suffering damage.

The device is switched on and off using the main switch (A) on the

right hand side.

A few seconds after the device has been switched on, the display

will show all display segments, the software version, operating

mode, target temperature and speed.

The device is now ready for operation.

RH basic

Observe the ambient conditions (temperature, humidity, etc.) listed

under Technical Data.

Make sure the contact plug (N) is plugged in.

Before switching the device on, turn the two rotary knobs on the

device to the off position.

Once these conditions are satisﬁed,

and the mains plug has been plugged

in, the device is ready to operate.

RH digital

Operating the device in mode A or B

Mode A

All settings will be stored if the device is switched off or disconnec-

ted from the power supply. The agitation and heating functions

will be set to OFF when the device is powered on.

Mode B

All settings will be stored if the device is switched off or disconnec-

ted from the power supply. The agitation and heating functions

will be set to ON or OFF when the device is powered on, depen-

ding on the previous status of the device.

Factory setting: mode A

The mode selected will be shown on the

display when the device is started up.

Change the mode

Setting the operation mode

mode

FMove device switch (A) to the OFF position

FPress and hold button (G and J)

FMove device switch (A) to the ON position

FRelease button (G and J) until mode changed

i  aThe set value is indicated on the

display b

Assembly of H 102.1 protection handle

i i

Protection handle should be assembled in place for safety!

Please note that slight residual odor could be smelt during ﬁrst-

heating of the heater.

We suggest to operate the unit under a fume hood during the ﬁrst use.

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 51 52

Comments to this Manuals

No comments

Ika RH digital User Manual Page 12

Comments to this Manuals

Related products and manuals for Equipment Ika RH digital